Getting Familiar with Plumbing: Before Bathtub Installation
Getting Familiar with Plumbing: Before Bathtub Installation
Blog Article
The author is making a number of good annotation about A Step-by-Step Guide to Installing a Bathtub as a whole in this post below.
Mounting a bath tub isn't exactly rocket science, but it does need strong plumbing, woodworking, and also occasionally, tiling skills. Replacing an old tub with a brand-new one is additionally a moderately difficult project. If the old bathtub is easily accessible, the job can relocate speedily; if you have to open a wall surface to remove the old tub as well as position the new tub, the job is a lot harder. In either case, the task is within a home handyman's skills, although you will certainly require a helper to leave the old bathtub and also set in the new one. Ensure you have actually certified yourself for the work as well as are comfortable trying it. As opposed to hiring a contractor to take control of a halfway-completed task, it is far better to think about utilizing one prior to you start. Chances are you may need a professional plumber to make tube links.
This write-up will assist you mount a brand-new tub in your washroom if you have actually currently bought a new bathtub as well as don't require to transform the setup of your previous water supply pipelines.
Your devices and product list must make up the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your setup, after that the first thing you must do is separate the supply of water. After doing so, activate the faucets to drain pipes any water staying in the system. The procedure of removing the existing taps can be fairly troublesome due to the limited gain access to that is usually the situation.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the taps. Have a towel prepared for the staying water that will certainly come from the pipelines. When the supply pipes have been eliminated, make use of the same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary taps from transforming during this process. Once the faucets have been eliminated, the holes in the bath/basin will have to be cleansed of any type of old securing substance.
Prior to carrying on to fit the brand-new faucets, compare the pipe links on the old taps to the new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet and the other end supplies a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will require decreasing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the mounting hole in the bath/basin making certain that the washers are in location in between the faucet and the sink. Safeguard the tap in position with the manufacturer provided backnut. As soon as the tap is firmly in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular tap connectors. The previous kind should be linked to the faucet ends first, tightening only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Setting up the Bathtub
Utilizing both wood boards under its feet, put the bath tub in the needed position. The wooden boards are valuable in uniformly spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 little points.
The next goal is to make certain that the bath tub is leveled all round. This can be attained by checking the spirit level as well as adjusting the feet on the bath tub until the spirit level reviews level.
To install faucets, fit all-time low of the outermost versatile faucet port to the suitable supply pipeline by making a compression join; after that do the exact same for the other tap.
Activate the water system and examine all joints and new pipework for leakages and tighten them if required. Fill up the bathtub as well as likewise check the overflow electrical outlet and the typical electrical outlet for leakages.
Ultimately, repair the bathroom paneling as described in the producer's user's manual. Tiling and sealing around the tub should wait up until the bathtub has actually been made use of a minimum of once as this will certainly settle it into its final setting.
Planning for the Setup
First of all, the sustaining framework provided with the bath must be fitted (if called for) according to the manufacturer's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to make certain that if the tap features a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is also practical to fit a supporting plate under the taps device to prevent strain on the tub.
Fit the adaptable tap ports to the bottom of both faucets making use of 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet with the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you use all of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must now prepare to be fitted in its final setting.
Tiling Around the Tub
In the location where the bath fulfills the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to break a rigid seal, causing the water to permeate the wall in between the bath as well as the tiling, causing difficulties with wetness and feasible leaks to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components and installations. They are marketed in tubes and cartridges, and are capable of sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill the tub with water prior to sealing, to permit the movement experienced when the bathtub is in use. The sealant can fracture rather early if you do not think about this motion before securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently offered on the market. It is recommended to fit the floor tiles using waterproof or water resistant glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a passionate person who reads on A Step-by-Step Guide to Installing a Bathtub, I figured sharing that portion was really useful. In case you enjoyed our blog entry if you please be sure to pass it around. Thank you for taking the time to read it.
Precise fixes offered. Report this page